How to Build a Table Saw Jointer Jig

Jointers are usually very expensive, bulky and not meant to be moved from one location to another. They are the best tools for straightening boards. You can use it to make one flat surface on a table saw, to square the board. Moreover, you can always buy one or build it in your workshop.

Table saws often have a simple jig that can do the work of a jointer. Therefore, today we will look at how you can easily build a table saw jointer jig, which can give you straight and clean edges that you can work on and make other joints.

Tools and Materials Needed

The difficulty level of this woodworking is moderate to easy, with zero finishing. You can complete it within 1-2 hours. Besides, this jig configuration plan is for boards no longer than 4 feet, in length.

  • A table saw
  • Cordless drill or power drill
  • ½-inch straight-cutting router bit
  • Fixed-base router with a router table
  • Tape measure
  • Pencil
  • 1-1x6x3 inches SPF Lumber
  • 1-12×4 inch piece of ¾-inch sanded AC, plywood
  • 2-½ x2 inch hex bolts with two flat washers, two lock washers as well as two wing nuts
  • 1-¼ inch deck screws
  • ¾ inch wood screw
  • ½ inch chisel
  • Two quick-release toggle clamps

Cut Guide Slots

In this tutorial, you will need ¾-inch plywood, of 12W by 48L inches and a 1×6 cut to 36-inches lengthwise. You will also need a 60-inch long strip of stock ripped to 3/4 by 3/8 or any other straight scrap stock.

Set the fixed base router with a ½ straight cutting bit, and then place it on the router table. Adjust bit height to 1/8 above table surface.
Make two slots on the 1×6, each an inch from the board′s end, perpendicular to its long axis. Each slot should stop at ¾ inch from the board′s edge.

The fence of the router table should be 1-inch away from the edge of the bit and make pencil marks on the fence, ¾-inch on each direction from edges of the bit. The pencil marks will indicate the beginning and end of points of the slot.

After which, you can start the router, ease the board down the bit with the leading edge at the far end of the pencil′s mark. Guide the board along the fence until its trailing edge meets the pencil mark trail, lift it off the bit and repeat the same process on the other slot.

You can then raise the router bit to another 1/8-inch and repeat the slot cuts until you finish. Take care when pushing the end grain against the fence on the router table, as it can bind to the fence, leading to kickbacks.

Moreover, work slowly and sure, dropping the speed of your router bit, a little to prevent the bit from burning.

Drill Bolt Holes

Cut 1/2-inch diameter holes on lower plywood. This is where the two hex bolts will go through and then to the slots that allow the jig to joint various board widths.

Here you will position upper board on plywood and center on the long axis, six inches from each end and 2-1/2 inch from the right edge of the lower plywood.

Make your pencil markings on each left side of the slot and into the plywood below. Then remove the upper board and drill 1/2 –inch hole on the plywood, at the two pencil markings.

Recess Bolt Head

First turn the plywood base of jointer jig and insert two bolts in the ½-inch bolts holes. Use a pencil to mark the edges of the hex bolts.
Remove the bolts and enough material to recess their heads into the base of the plywood. You can use a ½-inch bevel-edged chisel.

Assemble Jointer Jig

Turn plywood base over and attach upper half of jig by positioning slots over bolts. Finish each bolt with a flat washer, then a lock washer and finally a wingnut. Remember the lower half of the jointer jig has recessed hex bolts.

You can then test if the upper half will slide against the lower half, and be held securely and tightly with the wingnuts.

Attach and Adjust Clamps

Attach quick-release toggle clamps on upper jig portion, using four ¾ wood screws. Positioning, each clamp base evenly, about ¼-inch from the right edge of the upper jointer jig, about 2-inches inside the slots.

Then adjust the pads of the clamps, so they can secure/ hold any piece of one-by stock, be it 1×6 or 1×8. You can use any scrap piece of stock in the clamps, during the adjustment.

However, do not make it so tight, as the pressure can tear the clamps off the jig. You can use a pair of open-end wrenches.
Cut Miter Strip

Rip a piece of stock on your table saw, 5-feet and fit it on the left miter slot of your table saw. Verify your saw miter slot first, but it usually ranges from 3/4W-3/8H or more. Make sure the strip glides easily, with minimal play through the miter slot. Its important that you buy best table saw for the money because its a key component of your project. You can always read reviews on websites like BesthomeGears about such power tools.

Attach Miter Strip

Attach miter strip to jig base. Face the table saw, measure left side of the saw blade to the right edge of left miter slot, and then add 1/8-inch to this measurement.

Then turn over the jig, measure right-hand side distance. Use a straight edge to mark a parallel line at this distance from the right edge of the jig.

Lastly, position the strip′s wide edge against jointer jig base, on the edge of the line that is opposite the right side of jointer jig. Use 1-1/4-inch deck screws for attaching.

Moreover, pre-drill and countersink the deck screws to ensure their heads recess and never protrude past the face of the strip.

Trim Jointer Jig

Trim the edges of the jig, but first, make sure that the miter slot and jointer jig glides smoothly through the entire table length. After which, pull the jig toward your body, raise the blade over 3/4-inch start the saw and trim right side edge of jointer jig and you are through.

Additional Information on Use

Using a table saw jointer jig is very easy. Just position the wood board you want to square in the jig. Place the parts you want to remove just over the right edge of the jig, raise the blade a bit higher above the stock, start the saw, and trim the stock nicely.

Use a table saw with a fence if you plan to trim the other side of the stock, as a table saw jointer jig only straightens one side of the board edge.

Moreover, you can adjust the wingnuts, to narrow or widen the clamps, in order to accommodate various board widths.
Also, exercise caution and stand on the left side of the blade in case of a kickback. Never stand behind it.


There you have, an easy and straightforward way to building a table saw jointer jig. Follow these steps and you will never go wrong in any way.…

Tips, Advice And Ideas For Home Improvement Success

Do you have what it takes to do your own home improvement? Have you had previous success with fixing up your home in the past? Read on to discover some home improvement.

The more personal your renovations, the less likely it is that someone else will want to buy it for enough to cover the cost of the work.

It can cost a lot of money to install a new floor, and you should shop around for the best prices.Discount supply stores are very valuable as they can help you save money.

Chipping paint, and rotting decks with water damage can be seen easily when checking home you wish to buy. However, electrical issues, bad wiring, foundation damage and other issues require an inspector to notice.

Visit open houses for newer homes before engaging in a renovation project. Lots of model homes are a great place to get good ideas.

Basements typically have little in the way of natural lighting. Be sure to have an artificial lighting that your basement is livable. Some basements have walls are high enough to protrude above the ground outside. You might be able to put windows in this area if this is the lighting of your basement.

Chair cushions eventually flatten with heavy use. A great way to restore such cushions is setting them outdoors in the sun. The sun will help remove some of the bounce by evaporating moisture that has accumulated in the cushions and give them new bounce. Be aware that fabric color is subject to fading in the sun, because the colors of the fabric can fade in the sun.

Replacing the flooring in any room can be an expensive project so you must prepare accordingly.One way to do is simply remove the flooring that’s in place and stain the concrete instead. This industrial-inspired look is both versatile and industrial aesthetic that can work well with a variety of different decors.

Move furnishings away from the walls to make the room look bigger.This makes the room feel larger while giving it a more modern and contemporary appearance.

To maintain hot water while traveling through pipes during the winter, don’t forget to insulate your pipes to keep the lines from freezing.Weatherizing tape is easy to apply to plumbing lines is available at your local hardware store. The tape plugs into your pipes from freezing which could lead to a pipe burst.

Before you start a project for home improvement you may wish to speak with the neighbors about it. Living next to a construction job is a real annoyance. Your neighbors will be significantly less annoyed if they know what to expect any potential disturbances.

Use fruits and flowers to freshen up your kitchen. This is cheap to do and will improve the look of effort to get great results in your kitchen.

These repairs usually require holes to be drilled into walls and floors, so make sure they are taken care of before having other things done.

New blinds are an easy home improvement task that provides surprising results.

These are common in older homes and can become huge problems. It is much easier to tackle them at their onset and quick. A delay can turn into major headaches. A bit of bleach can work miracles on little mold problems. You can usually sand to get rid of rust.

Home improvement is such a diverse field that you can spend a lifetime learning about it. You’re always learning and finding out how to improve your skills. Use the tips that you read in the above article to become a great handyman or woman.…

New To Home Improvement? Check This Out!

Many people are not comfortable with home improvement is impossible to do by themselves. People often fail when they are always tackling home improvement projects on their own and failing. Home improvement really isn’t as hard to do. The following article has tips to help you update and fix your home.

A great tip for home improvement project you undertake. You will enjoy your home through personal panache.

If you wait till the project has begun to ask, you might find it difficult to find someone to help you.You also might have problems finishing your work, adding extra stress to your work.

Do not demolish too quickly as you start your home improvement task. Always double check structures behind walls and cabinets before going to tear it down. It can be really expensive to fix any electrical or plumbing systems by mistake.

Check out the credentials of any company you are considering. Try to work with a company that has a good reputation.

Make sure to take full advantage of your outdoor space. You can turn your backyard into the house. It’s the ideal spot for entertaining outside or just enjoying some fresh air and relaxation after coming home from a hard day’s work.

A well-made and contemporary front door can raise the property value of your property. If you want to add a bit of pizzazz to your front door, you can choose from a lot of options.

It may be wise to paint before you install any flooring in those rooms. Even if you take extra precautions to protect the floor, you are sure to find a way to get some paint on your beautiful new flooring.

You can easily make your entrance look better and more attractive by simply replacing exterior doorknobs.This project that has a lot of your time. All you need is a screw driver. You can buy doorknobs at your home improvement store.

If you are not able to take good care of your yard, consider installing a low-maintenance yard. This usually will consist of a few rock beds that have hardy plants that don’t need a lot of water.This option is going to make it to where you time and costs on water or maintenance.

Give any room a new look by changing the window dressings. You can even switch out different colors or materials.

You can create a budget-friendly kitchen back splash by using varnish and varnish. Purchase wallpaper in a design you want. Measure space and then cut paper larger than the space. Put wallpaper paste on the paper and give it a few minutes. Hang the paper and then smooth out bubbles. Trim edges for just the right fit. Apply a layer of varnish with a paintbrush. Enjoy your new back-splash.

Have you taken a good look at your door handles on the doors in the house? Consider replacing the door handles for a stylish change.

Use a decorative painting technique if you don’t want to spend a dramatic effect within a room.

You can consider purchasing permeable house wraps, rigid foam insulation and complete wall-protective systems.

You must be sure to do research about the roofing company you’re considering before you sign a contract. You can check the BBB or do an online reviews from previous customers.

Don’t forget to properly replace or repair any damaged parts of your walls is a prerequisite to applying a new coat of paint.

As you can see by now, home improvement is thought of as impossible by many folks. Sometimes people do fail. Despite this fact, home improvement really isn’t all that hard. Just keep these tips in mind as you begin your project.…